ST06 Series

• Temperature limiter,
  for temperature monitoring, can be used as winding protection in electric motors or transformers and as a protective device in a variety of electrical appliances
• Compact and robust switch head
• Contact form: single pole, open on temperature rise, snap action
• Rated load
  10 A 250 VAC (resistive load)
  6,3 A 250 VAC (inductive load)
  40 A 24 VDC (resistive load)
• Insulated version of the electrical alive metal housing
  with insulation cap, sleeve or insulation of the switch head with epoxy resin
• Calibration temperature selectable from +60°C to +200°C, switching temperature pre-set at the factory,
  calibration tolerance: ±5 K (standard), differential: approx. 70% the selected calibration OFF temperature
• Maximum switch head temperature +200°C
• Low self-heating, as the bimetallic sensor element is not carrying current
• Lead wires:
  insulated stranded wire in accordance to UL,
  customized,
  standard conductor cross-section AWG 18 (approx. 1.0 mm²),
  insulation FEP (200°C, 300 V), PFA (250°C, 600 V), silicone (200°C, 600 V) or XLPE (150°C, 300 V)
• Approvals: VDE, UL, cUL

ST01H Series

• Temperature limiter, with electrical self-holding contact, excellent for motor and winding protection, and a large variety of appliances
• Contact form: Single pole, single throw; open on temperature rise
• Snap action device; quick break/quick make switching action
• Rated load:
  6,3 A 250 VAC 1.000 cycles
• Calibration OFF temperature selectable
  from +60°C to +180°C in increments of 5°C
• Factory preset fixed calibration temperature
• Calibration tolerance: ±5 K
• Maximum sensor head temperature of +180°C
• Low current sensitivity, the bimetallic element does not carry the circuit current
• Termination: Lead wire, stranded wire,
  cross–section 0.2 mm² (AWG 24), 0.3 mm² (22 AWG) or 0.6 mm² (20 AWG),
  XLPE, silicone, FEP or PFA insulation up to 250°C or 600 V nominal voltage
• Approvals: VDE, UL, C-UL

J-2 Series

• Thermal cut-out (SOD)
  A snap action thermostat that functions like a non-resettable type control.
  This single operation thermostat performs like a thermal fuse with the reliability
  of a 100% tested bimetallic thermal control.
• Contact form: Single pole, single throw; open on temperature rise
• Snap action device; quick break/quick make switching action
  Rated load:
  15 A 120 VAC (resistive load)
• Calibration OFF temperature selectable from +60°C to +160°C in 1°C increments
• Factory preset fixed calibration temperature
• Calibration tolerance customizable from ±5 K to ±10 K
• Maximum sensor head temperature of +180°C
• Bimetallic element carries the circuit current
• Integrated crimping connectors
• Customization of the lead wire and insulation is possible

H Series

• Thermal cut-out (SOD, bimetallic single operation device)
• Contact form: Single pole, single throw; open on temperature rise
• Snap action device; quick break/quick make switching action
• Factory preset fixed calibration temperature

  PEPI	Min. Calibration Temperature [°C]	Max. Calibration Temperature [°C]	Max. Current [A]	Max. Voltage	Approvals
  H Series	160	240	8/8/4	250 VAC/24/36 VDC	TÜV/c-UL
  H-3 Series	130	230	10/2	250 VAC/24 VDC	VDE/c-UL
  H-4 Series	130	230	0,5	50 VDC	VDE/c-UL
  H-5 Series	130	240	15/10	120/250 VAC	TÜV/c-UL
  H-7 Series	200	260	15	250 VAC	TÜV/c-UL
  H-8 Series	250	280	15	250 VAC/24 VDC	TÜV/c-UL

• Reset temperature: <-35°C

B Series

• Thermostat, temperature control
• Contact form: Single pole, single throw; open on temperature rise
• Creep action device
• Rated load:
  3 A 12 VDC
  3 A 24 VDC
• Calibration OFF temperature selectable from +5°C to +150°C in 1°C increments
• Factory preset fixed calibration temperature
• Calibration tolerance customizable from ±5 K to ±10 K
• Differential between OFF and ON calibration temperature of 2 K to 10 K
• Bimetal does not carry current
• Contacts are gold plated (also usable for applications with low voltage and small current)
• Customization of lead wire and insulation possible
• Approvals: UL, CSA

W Series

• Thermal protector for use in all types of appliances and excellent for motor and winding protection
• Contact form: Single pole, single throw; open on temperature rise
• Snap action device; quick break/quick make switching action
• Rated load:
  37 A 250 VAC (resistive load)
  10 A 250 VAC (inductive load)
• Calibration OFF temperature selectable from +70°C to +150°C in 1°C increments
• Factory preset fixed calibration temperature
• Calibration tolerance customizable to either ±5 K or ±10 K
• Differential, depending on chosen no-load calibration temperature, ranging between 10 K and 80 K
• Maximum sensor head temperature +180°C
• Bimetallic element carries the circuit current;
  current sensitivity can be customized using the specific resistance of the bimetal
• Customization of lead wire and insulation is possible
• Approvals: VDE, UL, CSA

N Series

• Thermostat, temperature control
• Contact form of models N, N-1, N-2: single pole, single throw; open on temperature rise
  Contact form of model NR: single pole, single throw; close on temperature rise
• Creep action device
• Rated load:
  8 A 12 VDC
  4 A 24 VDC
  Model N-1, N-2: Short circuit current until 100 A 12 VDC
• Calibration OFF temperature selectable from
  +30°C to +130°C (Model N, N-1, N-2);
  +30°C to +125°C (Model NR); with 1°C increments
• Factory preset fixed calibration temperature
• Calibration tolerance customizable from ±3 K to ±10 K
• No differential between OFF and ON calibration temperature, due to creep action contacts
• Bimetal carries current
• Current sensitivity customizable through the specific resistance of the sensing element (Models N, N-1, or N-2)
• Contacts are gold plated (also usable for applications with low voltage and small current)
• Customization of lead wire and insulation is possible
• Approvals: UL, C-UL

C Series

• Thermostat, temperature control
• Contact form of models C and CH: single pole, single throw; open on temperature rise
  Contact form of model CR: single pole, single throw; close on temperature rise
• Creep action device
• Rated load:
  8 A 12 VDC
  4 A 24 VDC
• Calibration OFF temperature selectable from +5°C to +200°C in 1°C increments
• No differential between OFF and ON calibration temperature, due to creep action contacts
• Bimetal carries current
• Contacts are gold plated (also usable for application with low voltage and small current)
• Customization of lead wire and insulation is possible
• Approval: UL, CSA

V Series

• Temperature control, usable as i.e. charge and short circuit protection in battery packs
• Contact form: Single pole, single throw; open on temperature rise
• Snap action device; quick break/quick make switching action
• Rated load:
  10 A 12 VDC 10,000 cycles
  5 A 24 VDC 10,000 cycles
  Short circuit currents until:
  150 A 12 VDC 500 cycles
• Calibration OFF temperature selectable from +45°C to +100°C in 1°C increments
• Factory preset fixed calibration temperature
• Calibration temperature tolerance customizable ±5 K to ±10 K
• Differential, depending on no-load calibration temperature, ranging from 4 K to 35 K; switch back temperature: >35°C
• Bimetallic element carries the circuit current;
  current sensitivity can be customized using the specific resistance of the bimetal (model V or VA)
• Contacts are gold-plated
• Customization of lead wire and insulation is possible
• Approvals: UL, CSA

ST01 Series

• Temperature limiter, excellent for motor and winding protection, and a large variety of appliances
• Contact form: Single pole, single throw; open or close on temperature rise
• Snap action device; quick break/quick make switching action
• Rated load:
  6,3 A 250 VAC (resistive load)
  5 A 125 VAC (resistive load)
• Calibration OFF temperature selectable
  from +60°C to +250°C in increments of 5°C
• Factory preset fixed calibration temperature
• Calibration tolerance: ±5 K
• Differential 20 to 50 K depending on the chosen calibration temperature
• Maximum sensor head temperature of +200°C
• Low current sensitivity, the bimetallic element does not carry the circuit current
• Termination: Lead wire gauge 0,325 mm² (AWG 22) either with
  XLPE isolation (150°C, 300 V) or PFA isolation (250°C, 600 V),
  alternatively lead wire gauge 0,205 mm² (AWG 24) wit Silicone isolation (200°C, 600 V),
  or solid bare wire (lead frame) for PCB assembly
• Approvals: VDE, UL, C-UL